ServoOmni

Current Version - 1.1.14

1. If you need to download the installer from the office rather than run Check For Updates directly from your saw, contact Technical Support at MiTek for details.

2. Updating to this version will remove the cuttings from your cut list. Please complete your cutlist prior to update.

3. Updating to this version will make a copy of your history database to C:\Program Files\Koskovich\ServoOmni\Backup\. To restore the history file, copy it to C:\Program Files\Koskovich\ServoOmni\Config\.

Downloads
 
ServoOmni Reports v1.0.0 - installer
.NET Framework 2.0 - installer

1.1.14 

  • Fixed Defect - Bottom chords being rejected for cuts too long. Changed to flip member so long cut is on blade #3.
  • Fixed defect - Wedge blocks being thrown violently across the room. Raised blade #3 to stop it.

1.1.12 

  • Added feature - Can now flip parts to cut them in a different orientation from the main screen. Right-click on the part, and select Top-Bottom or Left-Right.
  • Added feature - Can configure the default orientation for part types 2 and 3. See Tools/Options/Orientation and select the proper orientation.
  • Added feature - When run in Simulator mode, a graphic view of the blades and conveyors and transport is shown to depict how the saw moves into a setup. See Tools/Visualize.
  • Fixed defect - Part types that had two negative cuts on the trailing end would not import properly.

1.1.11

  • Fixed defect - the fix for the 2x10 part type 13 with 45 heels blade 4 setting up high in version 1.1.10 created a problem with scissors heels - blade 4 would setup on the right plane, but up too high in some cases.

1.1.10 

  • Added feature - Either keyin screen can be set as the default, the standard keyin or the enhanced keyin.
  • Improvement - Will re-orient parts that are likely to generate a telescope error on arm 4.
  • Fixed defect - on short heels on tall stock, blade 4 would set up too high.
  • Fixed defect - no error was displayed when there is only one trailing cut and its made on arm 3 which has an error.
  • Fixed defect - arm errors on 1 and 4, or 1 and 3 (when the cut is made there instead of 4) were not being handled properly when a file was imported.
  • Fixed defect - part validation wasn't being called on a keyin part.

1.1.05 

  • Added feature - Either keyin screen can be set as the default, the standard keyin or the enhanced keyin.
  • Improvement - Will re-orient parts that are likely to generate a telescpe error on arm 4.
  • Fixed defect - on short heels on tall stock, blade 4 would set up too high.
  • Fixed defect - no error was displayed when there is only one trailing cut and its made on arm 3 which has an error.
  • Fixed defect - arm errors on 1 and 4, or 1 and 3 (when the cut is made there instead of 4) were not being handled properly when a file was imported.
  • Fixed defect - part validation wasn't being called on a keyin part.
1.1.03
  • Added feature - Added the Truss field to the cut list.
1.1.02
  • Added feature - Added the Truss field as a printable field (used when importing .xml files).
  • Improvement - Updated to .NET 2.0 Framework.
  • Improvement - Decreased minimum length requirement to 95" for parts of large stock widths (x6 and up) to use the standard conveyor positioning.
  • Fixed defect - would not work in 4-blade mode.
  • Fixed defect - inital sort order when program was started with a previously loaded cutlist was incorrect.
  • Fixed defect - exception was thrown when setting scissors heel to zero.
  • Fixed defect - label shown for default job field was incorrect.
  • Fixed defect - Added variation of part type 9 that could not be parsed previously.
  • Fixed defect - when the scarf angle is less severe than the scissors heel angle, it created an invalid part with no error message.
  • Fixed defect - Added variation of part type 6 that wouldn't import.
  • Fixed defect - if a database was opened by another application, the compress would fail and the application couldn't continue.