Cyber® A/T Specifications

Physical Data

  • Overall width: 15’ 1” (fully assembled) 
  • Overall height: 9’ 1”
  • Overall saw length: 32’ (w/o incline conveyor)
  • Overall saw length: 43’ (with incline conveyor)
  • Shipping weight: 18,000 lbs.
  • #1 Saw – 7 hp, 3600 rpm with 20” carbide tip blade (+15º through –90º)
  • #2 Saw – 7 hp, 3600 rpm with 16” carbide tip blade (-15º through +90º)
  • #3 Saw – 7 hp, 3600 rpm with 16” carbide tip blade (-15º through +90º)
  • #4 Saw – 7 hp, 3600 rpm with 20” carbide tip blade (+15º through –90º)
  • #5 Saw – 13 hp, 1800 rpm with 32” carbide tip blade (-15º through +90º)
  • Air requirements: 100 psi

Performance Data

Manual Mode:

  • Min. straight cut length: 11”
  • Min. cut with four 45º cuts: 17”

Automatic and Semiauto Mode:

  • Min. straight cut length: 14”
  • Min. cut with four 45º cuts: 22”

Performance Data for All Modes:

  • Max. lumber size: 2 x 12 and 4 x 2
  • Max. straight cut length: 20’ 0”
  • Max. scarf cut length with 32” blade: 29-1/2”
  • Max. scarf cut length with 20” blade: 16” 
  • Max. scarf cut length with 16” blade: 10-1/2”  
  • Powered centerline adjustment to +/- .005” accuracy on all 5 saws
  • Powered angulation to +/- .10º accuracy on all 5 saws
  • Powered carriage travel to +/- 1/16” accuracy

Features

  • Absolute encoders for accurate positioning
  • Powered hold-down adjustment, vertical and horizontal
  • Powered horizontal adjustment of infeed conveyors
  • Powered lateral adjustment for in- and out-of-cut on #5 saw
  • Powered vertical adjustment for out-of-cut on #1, #2, #3 and #4 saws
  • 24” wide full length waste conveyor belt
  • Electronic lumber counter
  • Heavy-duty 2120 infeed chains with flights to push lumber through the saw 
  • Rack and pinion adjustable lumber stop
  • Center lumber support bar
  • Heel cut skid bar to support end of board (2nd bar is optional) 
  • Floor truss web riser bars for cutting 4 x 2 boards
  • Powerful Dell® PC with Windows® operating system located in a climate-controlled enclosure, away from the vibration of the saw
  • Touch screen monitor located on the saw
  • English and Spanish operating software on every saw

Electrical Data

  • Voltage: 230 VAC (others require transformer)
  • FLA plus control amps: 160.6 amps
  • Equipment disconnect protection: 200 amps
  • All electrical panels are UL Listed
Safety Data
  • Pneumatic brakes on all blades
  • Master operator shutoff control
  • Perimeter safety cable
  • Safety-rated emergency stops
  • Bilingual safety labels

Options

  • #6 Saw – 13 hp, 1800 rpm with 32” carbide tip blade and powered centerline and angle adjustment
  • 12’ incline waste conveyor mounted at either end
  • Catcher Display
  • Inker
  • Various material handling options
  • Spanish equipment manual available

     
NOTE: For single-piece bottom chords with a pitch less then 4/12, on lumber larger than 2x4 - Blade #6 is required.
 
Machine specifications subject to change without notice.

 This page last modified on 9/14/2007